Warning Cookies are used on this site to provide the best user experience. If you continue, we assume that you agree to receive cookies from this site. OK


Body Casting Alginate

If you are looking to take an impression somewhere from the human body then most mould making materials are not up to the job, mainly for health reasons. We do not recommend ANY product to be used on the skin other than our Pro Alginate Series. However our Pro Alginate can also be used to bed formers into when using our RTV's. Its easier to remove than clay or plaster when dry!

Made from natural materials and with limited additives, Alginates cure very quickly. However they can only be cast into once. We stock two grades a fast cure and slow cure which offer 4 minute set or 13 minute set. The slower set should be used to cover larger areas like the abdomen or where more care needs to be taken such as the face. Our alginate does not have a colour change system so you will need a stopwatch!

The most popular method for replication is to cast first in the alginate mould with a quality plaster, like Herculite 2 or Crystacal R and then make an RTV mould from that cast. This allows you to use products that may otherwise be harmful. DO NOT try to use Polyesters, Epoxies or Polyurethanes in alginate, they will not necessarily cure correctly (however we have not tested all our resin systems in alginate!). Silicone on the other hand will cure well in an alginate mould.

If your alginate is curing to fast to work with try reducing the water temperature and adding extra water to the product which will retard its cure. Be careful though, too much water will weaken the alginate significantly. For large areas a plaster support case should be used to retain the mould dimensions.

This is the only alginate we have found so far with a Skin Safe Declaration. Tested by manufacturer as no major hazard. So a brilliant moulding material for younger casters, along with our Viscolo 22!

£9.35 (£11.22 inc tax)
No Technical Sheet Available Material Safety Data Sheet (MSDS / CoSHH) Please note that we no longer print and include datasheets with your order. All datasheets are available for download on the item where your purchase was made. It is the responsibility of the purchaser to download and read the information. Please think of the environment before deciding to print!, Alginates are an extremely easy to use, single use replication system. Essentially a powder, water is added at 2:1 to obtain a workable paste or semi liquid. We offer two types of alginate, FAST and SLOW. Fast will set in around 4 mins, Slow in approximately 9-10 minutes. There is no colour change with our system, its not needed, use a stopwatch. Also ensure water is room temperature. Hot water accelerates, cold retards the set time. Excessive water will also retard the times, however also weakens the alginate. Once set these moulds must be kept moist or they will break up very quickly. We recommend using a fine plaster like Herculite 2 to cast in this mould type. Being stronger and finer its a better option. Plaster of Paris is soft enough that as you remove the alginate it may break. 1. Approximate the volume you need for the mould 2. Take one third this volume as alginate powder and add that to an oversized mixing vessel 3. Add the remaining two thirds volume as water, starting the stopwatch as you tip it in 4. Mix briskly, potlife is short! 5. Scoop up the mass into a bag if taking a hand or foot impression and squeeze around the hand. If using on the body spread like butter 6. Wait for the cure time to pass. The alginate should be firm but a bit flexible. Manipulate the item from the mould 7. Fill immediately with plaster or seal in a bag to keep moist TOMPS TIPS --Alginate may be pretty much harmless but does contain some substances you shouldn't eat! --Avoid prolonged skin contact --Use a greasy moisturiser like nivea to act as a release agent
Body Casting Alginate for impressions from the body. Hands, feet, face, torso! Two speeds! 3-4 mins and 9-13 mins!
In stock