Warning Cookies are used on this site to provide the best user experience. If you continue, we assume that you agree to receive cookies from this site. OK

TOMPS Products

£38.25
For soaking plaster to make it a little more weather proof. It prevents water damage and frost damage.
In stock

£4.21
Marble Flour for simulating the cool touch of marble in resins & Marble Sugar for bulking and adding weight
In stock

£17.99

Basic water based clay for sculpting. Not air drying, no nasty fibres! Must be kept moist during use.

In stock

£107.83
1.25mm 18 guage tie wire for hanging plasterware and armature wire for stop motion.
In stock

£5.32
2 Sizes - Measures either 15ml or 80 ml for Small & Large Respectively.
In stock

£2.49
Please note that we no longer print and include datasheets with your order. All datasheets are available for download on the item where your purchase was made. It is the responsibility of the purchaser to download and read the information. Please think of the environment before deciding to print!, GRP Fibre Glass Polyester Casting Resin or Polyester Gelcoat 1. Weigh out the desired volume of resin or gelcoat into a suitable container 2. Calculate the catalyst required at a ratio of 1.5-3% by weight 15g to 30g per kilo 3. If preferred add catalyst by volume at 13-26ml per 1000g 4. Stir very well, trying not to entrap any air and ensuring you get right to the edges and bottom 5. To be sure of full catalysation, tip from one pot to another after first mix and re-mix 6. Allow to stand for a few moments for air release (casting resin only) 7. Tip into the mould or paint onto the surface 8. Allow to cure (see the data sheet 6060_TECH.pdf (resin) or neo2000_TECH.pdf (gel) for cure times) 9. Cure times will vary on catalyst added and ambient temperatures. In cold climate add extra catalyst to a max. of 4% --Ensure your mould is free of water or dampness before casting- this will inhibit cure in top layers --Try not to cast in freezing cold or overly damp conditions --Ensure you resin is fully mixed, if it is not you will get pockets of uncured resin --Be as accurate as possible with weighing catalyst and resin - buy digital scales 1g increment for larger volumes, 0.1g increments for less --Ensure you are adding the right amount of catalyst. Add more if your mould is dry and resin is fully mixed yet still tacky on demould --In cold conditions you will need more catalyst. If you get yellowing or cracking that is too much catalyst! --Wipe uncured surfaces with acetone and buff with a wax to save the piece, though this is not guaranteed to save it! --If your resin is colder than 23 celsius and the ambient temperature is cold then the cure time will substantially increase.
MEKP Catalyst for curing Polyester Resins & Gelcoats
In stock

£4.99
Please note that we no longer print and include datasheets with your order. All datasheets are available for download on the item where your purchase was made. It is the responsibility of the purchaser to download and read the information. Please think of the environment before deciding to print!

Vermiculite Medium and Superfine Primarily used for lightening plaster and for creating effects on the face of casts

In stock

£4.79
CE Marked & Approved Safety Hat for site work etc.
In stock

£5.99
Two varieties a clear low duty and a black heavy duty, both with ties.
In stock

£9.08
Standard Cotton Whites for plasterers. Enter your waist size, we will select the closest size up!
In stock

£0.93
Heavy duty glove, much longer lasting than traditional disposables.
In stock

£8.99
Lightly powdered gloves for general protection of hands.
In stock

£0.75
Standard proection against noise pollution and risk. -27dB
In stock

£7.67
Good quality zinc plated screws for fixing cornice.
In stock

£6.42
Good quality zinc plated screws for fixing cornice.
In stock

£5.61
Good quality zinc plated screws for fixing cornice.
In stock

£4.66
Good quality zinc plated screws for fixing cornice.
In stock

£4.07
Good quality zinc plated screws for fixing cornice.
In stock

£12.99
Please note that we no longer print and include datasheets with your order. All datasheets are available for download on the item where your purchase was made. It is the responsibility of the purchaser to download and read the information. Please think of the environment before deciding to print!

A basic sandable sealer for application to porous materials prior to moulding. Will seal plaster and mortar.

In stock

£2.49
General purpose plastic spreader. Apply gelcoat, filler or even strike off a cornice mould.
In stock